a 0.6 kg drawbar A hanging from a 2.8 kg spool G with a radius of gyration of kg = 33.6 mm and a diameter d = 28 mm. how fast is the drawbar falling when it has descended 0.5 m?
Answers
The drawbar falls at a speed of approximately 2.70 m/s when it has descended 0.5 m.
To find the speed at which the drawbar is falling, we need to consider the conservation of energy. Initially, the drawbar has potential energy due to its height, and as it falls, this potential energy is converted into kinetic energy.
The potential energy (PE) of the drawbar at a height h is given by:
PE = mgh,
where:
m = mass of the drawbar (0.6 kg),g = acceleration due to gravity (9.8 m/s²),h = height of descent (0.5 m).The kinetic energy (KE) of the drawbar is given by:
KE = (1/2)mv²,
where:
m = mass of the drawbar (0.6 kg),v = speed of the drawbar.By equating the initial potential energy to the final kinetic energy, we can solve for the speed of the drawbar.
mgh = (1/2)mv².
Simplifying the equation, we get:
v = √(2gh).
Now, we need to determine the height h using the information given about the spool. The radius of gyration [tex]k_{G}[/tex] is related to the diameter d as follows:
[tex]k_{G}[/tex] = d/2.
Given the diameter d = 28 mm, we can calculate the radius of gyration [tex]k_{G}[/tex] as:
[tex]k_{G}[/tex] = 28 mm / 2 = 14 mm = 0.014 m.
The height h can be determined by subtracting the radius of gyration from the descent distance:
h = 0.5 m - 0.014 m = 0.486 m.
Now we can calculate the speed v using the derived height h:
v = √(2 * g * h)
= √(2 * 9.8 m/s² * 0.486 m)
≈ 2.70 m/s.
Therefore, when the drawbar has descended 0.5 m, it is falling at a speed of approximately 2.70 m/s.
The complete question should be:
A 0.6 kg drawbar A hanging from a 2.8 kg spool G with a radius of gyration of k[tex]_{G}[/tex] = 33.6 mm and a diameter d = 28 mm. How fast is the drawbar falling when it has descended 0.5 m?
The drawbar falls at ________ m/s.
To learn more about conservation of energy, Visit:
https://brainly.com/question/166559
#SPJ11
Related Questions
Calculate the resistance of a wire which has a uniform diameter 10.74mm and a length of 70.63cm If the resistivity is known to be 0.00092 ohm m Give your answer in units of Ohms up to 3 decimals. Take it as 3.1416 Answer:
Answers
The resistance of the wire is approximately 0.007 ohms.
To calculate the resistance of the wire, we can use the formula: R = (ρ * L) / A where R is the resistance, ρ is the resistivity, L is the length of the wire, and A is the cross-sectional area of the wire. The cross-sectional area of the wire can be calculated using the formula:
A = π * r^2
where r is the radius of the wire.
Given that the diameter of the wire is 10.74 mm, we can calculate the radius as:
r = (10.74 mm) / 2 = 5.37 mm = 0.00537 m
Substituting the values into the formulas, we have:
A = π * (0.00537 m)^2 = 0.00009075 m^2
R = (0.00092 ohm m * 0.7063 m) / 0.00009075 m^2 ≈ 0.007168 ohms
Therefore, the resistance of the wire is approximately 0.007 ohms.
To learn more about, resistance, click here, https://brainly.com/question/31367014
#SPJ11
A cylinder with a piston contains 0.190 mol of nitrogen at 2.00×105 Pa and 320 K . The nitrogen may be treated as an ideal gas. The gas is first compressed isobarically to half its original volume. It then expands adiabatically back to its original volume, and finally it is heated isochorically to its original pressure.
1-
Find the work done by the gas during the adiabatic expansion.
Express your answer in joules.
2-
Find the heat added to the gas during the adiabatic expansion.
Express your answer in joules.
Answers
The work done by the gas during the adiabatic expansion is -4.77 × 10³ J. The heat added to the gas during the adiabatic expansion is 4.77 × 10³ J.
N = 0.190 mol
P1 = 2.00 × 10^5 Pa
V1 = ? = volume of the gas
T1 = 320 K
Let's calculate the initial volume of the gas using the ideal gas law
PV = nRT
V = (nRT) / P1 = (0.190 mol × 8.31 J / mol K × 320 K) / 2.00 × 10^5 Pa
V1 = 0.00994 m³
Now, let's calculate the final volume of the gas, which is equal to half the initial volume since it is compressed isobarically. Thus, V2 = V1 / 2 = 0.00994 m³ / 2 = 0.00497 m³.
1. Work done by the gas during adiabatic expansion:Adiabatic process means that there is no heat transfer (Q = 0) between the gas and the surrounding. Adiabatic process can be defined using the following equation:
PVγ = constantwhere γ = Cₚ / Cᵥ is the heat capacity ratio. During the adiabatic expansion, the volume of the gas increases, so pressure and temperature decrease. The initial pressure of the gas is P1 = 2.00 × 10^5 Pa. Since the process is adiabatic, the final pressure can be calculated as:
P1V1γ = P2V2γ⇒ P2 = P1 (V1 / V2)γ = (2.00 × 10^5 Pa) (0.00994 m³ / 0.00497 m³)(7 / 5)P2 = 8.02 × 10⁴ Pa
W = (P2V2 - P1V1) / (γ - 1)⇒ W = [(8.02 × 10⁴ Pa)(0.00994 m³) - (2.00 × 10^5 Pa)(0.00994 m³)] / (7 / 5 - 1)W = -4.77 × 10³ J (The negative sign indicates that work is done by the gas during adiabatic expansion)
Hence, the work done by the gas during the adiabatic expansion is -4.77 × 10³ J.
2. Heat added to the gas during adiabatic expansion:Heat added to the gas during adiabatic expansion is given by the first law of thermodynamics as:
ΔU = Q - W
where ΔU is the change in internal energy of the gas. Since the process is adiabatic, Q = 0.
Thus,ΔU = - W⇒ Q = W = 4.77 × 10³ J.
Hence, the heat added to the gas during the adiabatic expansion is 4.77 × 10³ J.
Learn more about work done at: https://brainly.com/question/28356414
#SPJ11
A large gambling wheel turning
at a speed of 1.5 rev/s comes to rest in an agonizing time of 12s.
Find its deceleration in radians per second per second
Answers
The angular deceleration of the gambling wheel is -0.785 rad/s².
The initial angular velocity, ω₀ = 1.5 rev/s
The final angular velocity, ω = 0
Time taken, t = 12 s
The relation between angular velocity, angular acceleration and angular displacement is given by
ω = ω₀ + αt
Also, angular displacement, θ = ω₀t + ½αt²
If the wheel comes to rest, ω = 0
The first equation becomes α = -ω₀/t = -1.5/12 = -0.125 rev/s²
The value of α is negative because it is deceleration and opposes the initial direction of motion of the wheel (i.e. clockwise).
To find the angular deceleration in radians per second per second, we can convert the angular acceleration from rev/s² to rad/s².
1 rev = 2π rad
Thus, 1 rev/s² = 2π rad/s²
Therefore, the angular deceleration is
α = -0.125 rev/s² × 2π rad/rev = -0.785 rad/s² (to three significant figures)
Hence, the angular deceleration of the gambling wheel is -0.785 rad/s².
Learn more about angular deceleration :
https://brainly.com/question/12956978
#SPJ11
. You will need a partner. Run a tight figure-eight at increasing speed on a flat surface. Why is it difficult to run the figure-eight course at high speeds?
Answers
Running a figure-eight course at high speeds is difficult due to the increased centripetal force requirements, challenges in maintaining balance and coordination, the impact of inertia and momentum, and the presence of lateral forces and friction that can affect stability and control.
Running a figure-eight course at high speeds can be difficult due to the following reasons:
Centripetal force requirements: In order to make tight turns in the figure-eight pattern, a significant centripetal force is required to change the direction of motion. As the speed increases, the centripetal force required also increases, making it more challenging to generate and maintain that force while running.
Balance and coordination: Running a figure-eight involves sharp turns and changes in direction, which require precise balance and coordination. At higher speeds, it becomes more challenging to maintain balance and execute quick changes in direction without losing control.
Inertia and momentum: With increasing speed, the inertia and momentum of the runner also increase. This makes it harder to change directions rapidly and maintain control while transitioning between different parts of the figure-eight course.
Lateral forces and friction: During turns, lateral forces act on the runner, pulling them towards the outside of the turn. These lateral forces, combined with the friction between the feet and the ground, can make it difficult to maintain stability and prevent slipping or sliding, especially at higher speeds.
Overall, running a figure-eight course at high speeds requires a combination of physical strength, coordination, balance, and control. The increased demands on these factors make it challenging to execute the course smoothly and maintain stability throughout.
To learn more about Centripetal force visit : https://brainly.com/question/898360
#SPJ11
Frustrated with the Snell's pace of the progress of love,
he places an object 15 cm from a converging lens with a focal
length of 25 cm. What is the location of the image formed by the
lens?
Answers
The image is formed on the same side as the object and is a real image. The image is located at approximately 9.375 cm from the lens.
To determine the location of the image formed by a converging lens, we can use the lens formula:
1/f = 1/v - 1/u
Where f is the focal length of the lens, v is the distance of the image from the lens, and u is the distance of the object from the lens.
In this case, the object is placed at a distance of 15 cm (u = -15 cm) from the converging lens with a focal length of 25 cm (f = 25 cm).
Plugging these values into the lens formula, we can solve for v:
1/25 = 1/v - 1/-15
Multiplying through by 25v(-15), we get:
-15v + 25(-15) = 25v
-15v - 375 = 25v
40v = -375
v = -375/40
v ≈ -9.375 cm
Since the image is formed on the same side as the object, the distance is negative. Therefore, the image is located at approximately 9.375 cm from the lens.
Learn more about real image here; brainly.com/question/13197137
#SPJ11
Provide a well-developed reflection on two (2) machines that make your everyday life easier. For each machine you will: 1. State its purpose. 2. Explain how it makes your life easier. 3. Explain how your machine has impacted the socio-economic status of the modern family. 4. Explain the impacts (both negative and positive) of the machine on the environment. Discuss your thoughts with your classmates. Don't forget to cite any sources used.
Answers
machines have made our lives easier in many ways. However, they also have a negative impact on the environment. It is essential to strike a balance between convenience and sustainability.
In our modern era, machines have transformed the way we live our lives. They have made everyday living more convenient and more manageable. In this reflection, I will discuss two machines that make my everyday life easier. These machines are my smartphone and my dishwasher.
1. SmartphonePurpose: Smartphones have been designed to perform a wide range of functions. They can be used for communication, entertainment, shopping, and so much more. They are extremely versatile and can be customized to fit the needs of each individual user.How it makes my life easier: My smartphone makes my life easier in many ways.
I can use it to stay in touch with family and friends no matter where I am in the world. I can use it to access social media and stay up to date on the latest news and events.
I can also use it to make purchases and manage my finances.Impact on socio-economic status: Smartphones have had a significant impact on the socio-economic status of the modern family.
They have made it easier for families to stay connected even when they are far apart. They have also made it easier for people to work remotely and run businesses from anywhere in the world.Impact on the environment: Smartphones have a negative impact on the environment. They require the use of rare metals and other resources that are not sustainable. They also contribute to e-waste, which is a major problem in many parts of the world.2. DishwasherPurpose:
Dishwashers are designed to clean dishes quickly and efficiently. They are also more hygienic than washing dishes by hand.How it makes my life easier: My dishwasher makes my life easier by allowing me to clean my dishes quickly and without any effort. I simply load the dishwasher, add the detergent, and press start.Impact on socio-economic status: Dishwashers have had a significant impact on the socio-economic status of the modern family.
They have made it easier for families to manage their time more effectively. Instead of spending hours washing dishes by hand, families can spend more time together doing other activities.Impact on the environment:
Dishwashers have a negative impact on the environment. They use a lot of water and energy to operate, which contributes to climate change. They also require the use of detergents that contain chemicals that are harmful to the environment.
In conclusion, machines have made our lives easier in many ways.
However, they also have a negative impact on the environment. It is essential to strike a balance between convenience and sustainability.
To know more about machines visit;
brainly.com/question/19336520
#SPJ11
How many times greater than uea-level atmospheric pressure is the absolute pressure at a depth of 5.586 m? The density of sea wate is 1025 kg^2 m^3 .
Answers
Pressure ratio = (P₀ + (1025 kg/m³) * (9.81 m/s²) * (5.586 m)) / P₀
The absolute pressure at a certain depth in a fluid can be determined using the hydrostatic pressure formula:
P = P₀ + ρgh
where P is the absolute pressure at the given depth, P₀ is the atmospheric pressure at sea level, ρ is the density of the fluid, g is the acceleration due to gravity, and h is the depth.
Given that the density of seawater is 1025 kg/m³, and the depth is 5.586 m, we can calculate the absolute pressure at that depth.
P = P₀ + ρgh
P = P₀ + (1025 kg/m³) * (9.81 m/s²) * (5.586 m)
Now, to find how many times greater the absolute pressure is compared to sea-level atmospheric pressure, we can calculate the ratio:
Pressure ratio = P / P₀
Pressure ratio = (P₀ + (1025 kg/m³) * (9.81 m/s²) * (5.586 m)) / P₀
Using this formula, we can calculate the pressure ratio. However, we need the value of the atmospheric pressure at sea level to provide an accurate answer. Please provide the value of the atmospheric pressure, and I can help you calculate the pressure ratio.
LEarn more about Pressure ratio here:
https://brainly.com/question/31676704
#SPJ11
(a) An electron has a kinetic energy of 5.18 ev. Find its wavelength. nm (b) A photon has energy 5.18 eV. Find its wavelength. nm
Answers
a) λ = 6.626 x 10^-34 J·s / p, b) λ = (6.626 x 10^-34 J·s * 2.998 x 10^8 m/s) / (8.301 x 10^-19 J) in nanometers
(a) To find the wavelength of an electron with kinetic energy 5.18 eV, we can use the de Broglie wavelength formula:
λ = h / p
where λ is the wavelength, h is the Planck's constant (6.626 x 10^-34 J·s), and p is the momentum.
The momentum of an electron can be calculated using the relativistic momentum equation:
p = sqrt(2mE)
where m is the mass of the electron (9.109 x 10^-31 kg) and E is the kinetic energy in joules.
First, convert the kinetic energy from electron volts (eV) to joules (J):
5.18 eV * 1.602 x 10^-19 J/eV = 8.301 x 10^-19 J
Then, calculate the momentum:
p = sqrt(2 * 9.109 x 10^-31 kg * 8.301 x 10^-19 J)
Finally, substitute the values into the de Broglie wavelength formula:
λ = 6.626 x 10^-34 J·s / p
Calculate the numerical value of λ in nanometers (nm).
(b) For a photon with energy 5.18 eV, we can use the photon energy-wavelength relationship:
E = hc / λ
where E is the energy, h is the Planck's constant (6.626 x 10^-34 J·s), c is the speed of light (2.998 x 10^8 m/s), and λ is the wavelength.
First, convert the energy from electron volts (eV) to joules (J):
5.18 eV * 1.602 x 10^-19 J/eV = 8.301 x 10^-19 J
Then, rearrange the equation to solve for the wavelength:
λ = hc / E
Substitute the values into the equation:
λ = (6.626 x 10^-34 J·s * 2.998 x 10^8 m/s) / (8.301 x 10^-19 J)
Calculate the numerical value of λ in nanometers (nm).
Learn more about Planck's constant here:
https://brainly.com/question/24508217
#SPJ11
6. A stunt driver wants to make his car jump over 8 cars parked side by side below a horizontal ramp. (a) With what minimum speed must he drive off the horizontal ramp? The vertical height of the ramp is 1.5 m above the cars and the horizontal distance he must clear is 22 m. (b) If the ramp is now tilted upward, so that "takeoff angle" is 7.0° above the horizontal, what is the new minimum speed? (Chapter 3) 22 m F1.5m Must clear this point! 3882
Answers
Summary:
To jump over 8 cars parked side by side below a horizontal ramp, the stunt driver needs to have a minimum speed of approximately 23.8 m/s. If the ramp is tilted upward with a takeoff angle of 7.0° above the horizontal, the new minimum speed required will be slightly lower.
Explanation:
(a) In order to clear the 22 m distance and a vertical height of 1.5 m above the cars, the stunt driver needs to calculate the minimum speed required. We can solve this using the principles of projectile motion. The horizontal distance traveled can be calculated using the equation: range = horizontal velocity × time. The time can be calculated using the equation: time = vertical distance / vertical velocity. The vertical velocity can be calculated using the equation: vertical velocity = square root of (2 × acceleration due to gravity × vertical distance). By substituting the given values, we find that minimum speed required is approximately 23.8 m/s.
(b) When the ramp is tilted upward at an angle of 7.0°, the takeoff angle affects the vertical and horizontal components of the car's velocity. To find the new minimum speed required, we need to consider the vertical and horizontal components separately. The horizontal component remains the same as before, as the takeoff angle only affects the vertical component. We can find the new vertical component of the velocity using the equation: vertical velocity = horizontal velocity × tan(takeoff angle). By substituting the values, we find that the new minimum speed required, with the ramp tilted upward, will be slightly lower than 23.8 m/s.
Learn more about Range here
brainly.com/question/1066383
#SPJ11
An 84-g arrow is fired from a bow whose string exerts an average force of 115 N on the arrow over a distance of 79 cm. What is the speed of the arrow as it leaves the bow? Express your answer to two significant figures and include the appropriate units.
Answers
The speed of the arrow as it leaves the bow is approximately 46.59 m/s.
To find the speed of the arrow as it leaves the bow, we can use the work-energy principle. The work done on the arrow by the bowstring is equal to the change in its kinetic energy.
The work done on the arrow is given by the product of the average force (F) and the distance (d) over which the force is applied:
Work = F * d.
In this case, the average force is 115 N and the distance is 79 cm, which is equivalent to 0.79 m. Thus, the work done on the arrow is:
Work = 115 N * 0.79 m = 90.85 J.
Since the work done is equal to the change in kinetic energy, we can equate it to (1/2) * m * v^2, where m is the mass of the arrow and v is its velocity.
(1/2) * m * v^2 = 90.85 J.
Substituting the given mass of the arrow as 84 g, which is equivalent to 0.084 kg, we have:
(1/2) * 0.084 kg * v^2 = 90.85 J.
Simplifying the equation, we can solve for v:
v^2 = (2 * 90.85 J) / 0.084 kg.
v^2 = 2166.67 m^2/s^2.
Taking the square root of both sides:
v = √2166.67 m^2/s^2 ≈ 46.59 m/s.
Therefore, The speed of the arrow as it leaves the bow is approximately 46.59 m/s.
Learn more about speed here:
https://brainly.com/question/13943409
#SPJ11
Two point charges are stationary and separated by a distance r. which one of the following pairs of charges would result in the largest repulsive force?
Answers
The largest repulsive force is when the charges are equal and have the same magnitude, given that the charges are stationary and separated by a distance r.
Coulomb's law states that the electrical force between two charged objects is directly proportional to the product of the quantity of charge on the objects and inversely proportional to the distance between them. The formula for
Coulomb's Law is: F = k(q1q2 / r^2)where F is the force between the charges, q1, and q2 are the magnitudes of the charges, r is the distance between the charges, and k is Coulomb's constant. Coulomb's constant, k, is equal to 9 x 10^9 Nm^2/C^2.
To calculate the force, we have to multiply Coulomb's constant, k, by the product of the charges, q1 and q2, and divide the result by the square of the distance between the charges, r^2.
to know more about repulsive force here:
brainly.com/question/9099726
#SPJ11
If the efficiency of a solar panel is 20%, what minimum area of solar panel should someone install in order to charge a 2000 watt-hour battery that is initially empty? Assume 8 hours of sunshine and that sunlight delivers 1000 W/m2 O 1.0 m2 O 1.25 m2 O 0.125 m2 O 0.025 m2
Answers
The minimum area of the solar panel required, given an efficiency of 20% and the provided conditions, is 4.5 square meters.
To calculate the minimum area of a solar panel required to charge a 2000 watt-hour battery,
2000 Wh * 3600 s/h = 7,200,000 Ws.
Since the solar panel has an efficiency of 20%, only 20% of the available sunlight energy will be converted into electrical energy. Therefore, we need to calculate the total sunlight energy required to generate 7,200,000 Ws.
1000 W/m² * 8 h = 8000 Wh.
Area = (7,200,000 Ws / (8000 Wh * 3600 s/h)) / 0.2.
Area = (7,200,000 Ws / (8,000,000 Ws)) / 0.2.
Area = 0.9 / 0.2.
Area = 4.5 m².
Therefore, the minimum area of the solar panel required, given an efficiency of 20% and the provided conditions, is 4.5 square meters.
Learn more about solar panel here : brainly.com/question/26983085
#SPJ11
A solid sphere (I = 2MR2/5) rolls without slipping down a plane inclined at 29◦ relative to horizontal. What type of friction acts and what is the coefficient of friction? The answers are rounded to two significant digits.
Answers
The answers are rounded to two significant digits:* Type of friction: rolling friction* Coefficient of friction: 0.02
The type of friction that acts on a solid sphere rolling without slipping down a plane inclined at 29° relative to horizontal is rolling friction. Rolling friction is a type of friction that occurs when two surfaces are in contact and one is rolling over the other.
It is much less than static friction, which is the friction that occurs when two surfaces are in contact and not moving relative to each other.
The coefficient of rolling friction is denoted by the Greek letter mu (μ). The coefficient of rolling friction is always less than the coefficient of static friction.
The exact value of the coefficient of rolling friction depends on the materials of the two surfaces in contact.
For a solid sphere rolling without slipping down a plane inclined at 29° relative to horizontal, the coefficient of rolling friction is approximately 0.02. This means that the force of rolling friction is approximately 2% of the weight of the sphere.
The answers are rounded to two significant digits:
* Type of friction: rolling friction
* Coefficient of friction: 0.02
Learn more about friction with the given link,
https://brainly.com/question/24338873
#SPJ11
A 2kg ball is dropped from a height of 3m onto a spring that compresses 20cm. What is the spring constant of the spring?
Answers
The spring constant of the spring is 980 N/m.
The potential energy of the ball is given by the formula:
P.E = mgh
where m is mass, g is the acceleration due to gravity and h is the height from which the ball was dropped
P.E = 2 x 9.8 x 3= 58.8J
The potential energy is converted to kinetic energy as the ball falls towards the spring.
The kinetic energy of the ball is given by the formula:
K.E = ½ mv²
Where m is mass and v is velocity
K.E = (½) 2 v²
The velocity just before the ball hits the spring can be calculated using the conservation of energy principle, i.e the potential energy just before the ball hits the spring is equal to the kinetic energy just after the ball leaves the spring.
P.E before = K.E after
2 x 9.8 x 3
= (½) 2 v²v = 7.67 m/s
The force exerted by the ball on the spring when it is compressed by 20cm can be calculated using the formula:
Force = mass x acceleration
Force = 2 x 9.8
Force = 19.6 N
The spring constant of the spring can be calculated using the formula:
F = -kx19.6
= -k(0.2)
k = -19.6/(-0.2)
k = 980 N/m
Therefore, the spring constant of the spring is 980 N/m.
Learn more about The potential energy: https://brainly.com/question/24284560
#SPJ11
Line of charge A plastic rod is placed along the horizontal from x = -2.0 m tox=2.0 m. A charge Q = 5 nC is spread uniformly along the line. Use this information to answer each of the question on the side. 3 20 points D What is the value of the potential difference VA-Vg for a point A at coordinates XA = 4.1 m, y = 0 and a point B at coordinates XB = -9.1 m, y = 0.? Round off your answer to one decimal place but do not include the unit. Include the negative sign if appropriate. Type your answer...
Answers
The potential difference VA-VB between point A and point B is -78.9 V.
To calculate the potential difference between two points, we can use the formula:
ΔV = k * Q / r
where ΔV is the potential difference, k is Coulomb's constant (9.0 x 10^9 Nm^2/C^2), Q is the charge, and r is the distance between the points.
In this case, point A is located at coordinates (4.1 m, 0) and point B is located at coordinates (-9.1 m, 0). The distance between A and B is the difference in their x-coordinates:
r = |XA - XB| = |4.1 m - (-9.1 m)| = 13.2 m
Substituting the values into the formula, we have:
ΔV = (9.0 x [tex]10^9[/tex] [tex]Nm^2/C^2[/tex]) * (5 x [tex]10^-^9 C[/tex]) / 13.2 m
ΔV ≈ -78.9 V
Therefore, the potential difference VA-VB between point A and point B is approximately -78.9 V.
Learn more about potential difference
brainly.com/question/23716417
#SPJ11
018 Diagram "Q19. Which has the greater potential energy: a ball that is 10 feet above the ground or a hall with the same mass that is 20 feet above the bottom of a nearby 50-foot-deep well? 020. When a bow and row are cocked, a force is applied to the string in order to pull it back. Is the energy of the system 021, Suppose the physics instructor pictured in figure 6.15 gives the bowling ball a push as the releases it. Will the her chin be in danger? ed back from its equilibrium (center) b. At what points is the motion of the pendulum after kinetic energy the greatest? Explain At what points is the potential energy the greatest? Q23 For the pendulum in question 22, when the pendulum bob is halfway between the high point and the low point in its swing, is the total energy kinetic energy, potential energy. or boch? Explain 024. Is the total mechanical energy conserved in the motion of a pendolem? Will it keep swinging forever? Explain Q25 A sports car accelerates rapidly from a stop and burns rub ber (See everyday phenomenon bos 6.1.) h. Is energy conserved in this process? Explain QF *Q.X Q14 *035 "Q46 Q37.
Answers
For the following:
19. A ball that is 20 feet above the bottom has the greater potential energy. 20. The energy of the system is increased.21. Bowling ball a push as he releases it, her chin will be in danger.22. Kinetic energy of the pendulum is greatest at the lowest point in its swing. 23. The total energy is half kinetic energy and half potential energy.24. Total mechanical energy is conserved in the motion of a pendulum. 25. Energy is not conserved.What are the reasons for energy?Question 19
A ball that is 20 feet above the bottom of a nearby 50-foot-deep well has the greater potential energy. This is because the potential energy of an object is proportional to its height above a reference point. In this case, the reference point is the ground.
Question 20
When a bow and arrow are cocked, the energy of the system is increased. This is because the work done in pulling back the string is stored as potential energy in the bowstring.
Question 21
If the physics instructor in Figure 6.15 gives the bowling ball a push as he releases it, her chin will be in danger. This is because the bowling ball will have more kinetic energy when it is released, and it will therefore travel faster.
Question 22
The kinetic energy of the pendulum is greatest at the lowest point in its swing. This is because the pendulum bob is moving the fastest at this point. The potential energy of the pendulum is greatest at the highest point in its swing. This is because the pendulum bob is highest at this point, and therefore has the greatest amount of gravitational potential energy.
Question 23
When the pendulum bob is halfway between the high point and the low point in its swing, the total energy is half kinetic energy and half potential energy. This is because the pendulum bob is moving at its maximum speed, but it is also at its maximum height.
Question 24
The total mechanical energy is conserved in the motion of a pendulum. This means that the sum of the kinetic energy and the potential energy of the pendulum will remain constant throughout its swing. The pendulum will not keep swinging forever, however, because it will eventually lose energy to friction.
Question 25
No, energy is not conserved in the process of a sports car accelerating rapidly from a stop and burning rubber. This is because some of the energy is lost to friction as the tires slide on the road.
Find out more on energy here: https://brainly.com/question/18683052
#SPJ4
An image formed by a convex mirror (f = -32.8 cm) has a magnification of 0.148. How much should the object be moved to double the size of the image? (Give the displacement with a sign that indicates the direction. Assume that the displacement toward the mirror is positive.)
Answers
The object should be moved 16.4 cm towards the mirror to double the size of the image.
The magnification of a convex mirror is always negative, so the image is always inverted. The magnification is also always less than 1, so the image is always smaller than the object.
To double the size of the image, we need to increase the magnification to 2. This can be done by moving the object closer to the mirror. The distance between the object and the mirror is related to the magnification by the following equation:
m = -f / u
where:
m is the magnification
f is the focal length of the mirror
u is the distance between the object and the mirror
If we solve this equation for u, we get:
u = -f / m
In this case, we want to double the magnification, so we need to move the object closer to the mirror by a distance of f / m. For a focal length of -32.8 cm and a magnification of 0.148, this means moving the object 16.4 cm towards the mirror.
Learn more about convex mirror here; brainly.com/question/33230797
#SPJ11
A person with a digital camera uses a lens of focal length 25.0
mm to take a photograph of a 1.78-cm-tall seedling located 15.0 cm
from the camera.
Part A:
How far is the camera’s lens from its CCD
Answers
The camera's lens is located 5 cm from its CCD.
The distance between the camera's lens and its CCD (Charge-Coupled Device) can be determined using the lens equation:
1/f = 1/do + 1/di
where f is the focal length of the lens, do is the object distance (distance from the lens to the object), and di is the image distance (distance from the lens to the image formed on the CCD).
In this case, the focal length of the lens is given as 25.0 mm (or 0.25 cm), and the object distance is 15.0 cm.
Plugging the values into the lens equation:
1/0.25 = 1/15 + 1/di
Simplifying the equation:
4 = (1 + 15/di)
Rearranging the equation and solving for di:
15/di = 4 - 1
15/di = 3
di = 15/3 = 5 cm
Therefore, the camera's lens is located 5 cm from its CCD.
Learn more about focal length here:
https://brainly.com/question/1031772
#SPJ11
Which of the alternatives are correct for an elastic
collision?
a. In an elastic collision there is a loss of kinetic energy.
b. In the elastic collision there is no exchange of mass between
the bodie
Answers
The alternative that is correct for an elastic collision is that in an elastic collision there is no loss of kinetic energy and no exchange of mass between the bodies involved.
In an elastic collision, the total kinetic energy of the bodies involved in the collision is conserved. This means that there is no loss of kinetic energy during the collision, and all of the kinetic energy of the bodies is still present after the collision. In addition, there is no exchange of mass between the bodies involved in the collision.
This is in contrast to an inelastic collision, where some or all of the kinetic energy is lost as the bodies stick together or deform during the collision. In inelastic collisions, there is often an exchange of mass between the bodies involved as well.
Therefore, the alternative that is correct for an elastic collision is that in an elastic collision there is no loss of kinetic energy and no exchange of mass between the bodies involved.
To know more about elastic collision, refer
https://brainly.com/question/12644900
#SPJ11
A light ray of wavelength 589 nm traveling through air is incident on a smooth, flat slab of crown glass. If θ1 = 30° then: (A) Find the angle of refraction. (B) Find the speed of this light once it enters the glass. (C) What is the wavelength of this light in the glass? (D) What is the frequency of this light inside the glass? (E) Calculate the refracted exit angle. (F) Calculate the critical angle of refraction.
Answers
a. The angle of refraction is 52.19°.
b. The speed of light once it enters the glass is 1.97 × 108 m/s.
c. The wavelength of this light in the glass is 387.50 × 10⁻⁹ m.
d. The frequency of this light inside the glass is 5.08 × 10¹⁴ Hz.
e. The refracted exit angle is 52.19°.
f. The critical angle of refraction is 41.1°.
Given: Wavelength of light, λ = 589 nm
Angle of incidence in air, θ1 = 30°
Angle of refraction in glass, θ2 = ?
Formulae: Snell's law of refraction, n1 sin θ1 = n2 sin θ2. The refractive index of glass with respect to air, ng = 1.52 (Given) Critical angle of refraction, sin θc = 1 / n2
Part A: Angle of refraction is given by Snell's law of refraction
n1 sin θ1 = n2 sin θ2ng
sin θ1 = 1.52
sin θ2sin θ2 = (ng / 1)
sin θ1sin θ2 = 1.52 × sin 30°sin θ2 = 0.78θ2 = 52.19°
The angle of refraction is 52.19°.
Part B: Speed of light in air, v1 = 3 × 108 m/s
Speed of light in glass, v2 = ?
We know that the refractive index of glass is given by
ng = v1 / v2
where v1 is the speed of light in air and
v2 is the speed of light in glass
v2 = v1 / ngv2 = 3 × 108 / 1.52v2 = 1.97 × 108 m/s
The speed of light once it enters the glass is 1.97 × 108 m/s.
Part C: Wavelength of light in glass, λ2 = ?
We know that the refractive index of glass is given by
ng = c / v2
where c is the speed of light in vacuum and
v2 is the speed of light in glass
λ2 = λ / ng
λ2 = 589 × 10⁻⁹ / 1.52
λ2 = 387.50 × 10⁻⁹ m
The wavelength of this light in the glass is 387.50 × 10⁻⁹ m.
Part D: Frequency of light inside the glass, f2 = ?
We know that frequency is given by the formula,
v = f λ
where v is the velocity of light and
λ is the wavelength of light
v2 = f2
λ2f2 = v2 / λ2f2 = 1.97 × 10⁸ / 387.50 × 10⁻⁹f2 = 5.08 × 10¹⁴ Hz
The frequency of this light inside the glass is 5.08 × 10¹⁴ Hz.
Part E: Refracted exit angle is given by Snell's law of refraction
n1 sin θ1 = n3 sin θ3ng
sin θ1 = 1 sin θ3sin θ3 = ng sin θ1sin θ3 = 1.52 × sin 30°sin θ3 = 0.78θ3 = 52.19°
The refracted exit angle is 52.19°.
Part F: Critical angle of refraction is given by,
sin θc = 1 / n2sin θc = 1 / 1.52θc = sin⁻¹ (1 / 1.52)θc = 41.1°
The critical angle of refraction is 41.1°.
Learn more about angle of refraction at https://brainly.com/question/30952453
#SPJ11
A uniform copper rod sits with one end in a boiling beaker of water and the other end in a beaker of ice water (as shown)
Consider the heat that flows along the rod at points A (), B () and C ().
What ranking is correct if no heat is lost to the environment through the sides of the copper rod?
Answers
the ranking that is correct if no heat is lost to the environment through the sides of the copper rod would be point A > point B > point C.
The ranking that is correct if no heat is lost to the environment through the sides of the copper rod would be point A > point B > point C. Therefore, the correct option is option B.
Heat transfer is the process of the thermal exchange of energy from one point to another.
In heat transfer, heat energy is transferred from hotter objects to colder objects until they reach the same temperature. Heat transfer can take place through three main ways which are convection, conduction, and radiation.
A uniform copper rod is a good conductor of heat and the temperature is spread evenly across the rod. In the question given, the rod is sitting with one end in a boiling beaker of water and the other end in a beaker of ice water. The heat flows along the rod from the hot end to the cold end of the rod and the heat energy is transferred by conduction.
When the copper rod is placed with one end in a boiling beaker of water, the end of the copper rod will have the highest temperature and will be point A. The point where the rod enters the beaker of ice water will be point C, which is at a lower temperature than point A. The point at which the copper rod is halfway between the boiling beaker and the beaker of ice water will be point B. It is important to note that no heat is lost to the environment through the sides of the copper rod.
Therefore, the ranking that is correct if no heat is lost to the environment through the sides of the copper rod would be point A > point B > point C.
learn more about temperature here
https://brainly.com/question/27944554
#SPJ11
Determine the energies in ev of the fourth and fifth energy levels of the hydrogen atom. (a) fourth energy level
Answers
The energies in ev of the fourth and fifth energy levels of the hydrogen atom are respectively 0.85 ev and 1.51 ev
As per Bohr's model, the energies of electrons in an atom is given by the following equation:
En = - (13.6/n²) eV
Where
En = energy of the electron
n = quantum number
The given question asks us to calculate the energies in ev of the fourth and fifth energy levels of the hydrogen atom.
So, we need to substitute the values of n as 4 and 5 in the above equation. Let's find out one by one for both levels.
Fourth energy level:
Substituting n = 4, we get
E4 = - (13.6/4²) eV
E4 = - (13.6/16) eV
E4 = - 0.85 ev
Therefore, the energy in ev of the fourth energy level of the hydrogen atom is 0.85 ev.
Fifth energy level:
Substituting n = 5, we get
E5 = - (13.6/5²) eV
E5 = - (13.6/25) eV
E5 = - 0.54 ev
Therefore, the energy in ev of the fifth energy level of the hydrogen atom is 0.54 ev.
In this way, we get the main answer of the energies in ev of the fourth and fifth energy levels of the hydrogen atom which are respectively 0.85 ev and 0.54 ev.
Learn more about the hydrogen atom: https://brainly.com/question/30886690
#SPJ11
Young's double-slit experiment is performed with 570-nm light and a distance of 2.00 m between the slits and the scr Determine the spacing of the slits (in mm). mm (b) What If? What are the smallest and largest wavelengths of visible light that will also produce interference minima at visible light spectrum ranges from 400 nm to 700 nm.)
Answers
In this Young's double-slit experiment, (a) the spacing between the slits is 570 nm or 0.57 microns ; (b) the smallest wavelength of light that will produce interference minima at visible light spectrum ranges from 400 nm to 700 nm is 400 nm, and the largest wavelength is 700 nm.
a) Calculation of spacing of the slits in Young's double-slit experiment
The formula to calculate the distance between the slits is given by : d = λD/d where
d is the distance between the slits
λ is the wavelength of the light
D is the distance between the slits and the screen.
Therefore, we can use the given values to calculate the distance between the slits :
d = λD/d
⇒d = λD/2 m (given)
⇒d = 570 × 10⁻⁹ m × 2 m/2
⇒d = 570 × 10⁻⁹ m.
Hence, the spacing between the slits is 570 nm or 0.57 microns.
b) Calculation of smallest and largest wavelengths of visible light that will also produce interference minima at visible light spectrum ranges from 400 nm to 700 nm.
The formula to calculate the wavelength of the light is given by : λ = dsinθ/n where
d is the distance between the slits
θ is the angle of the screen
n is the order of the interference minimum or maximum.
The order of the minimum or maximum is an integer, starting from zero.
Therefore, we can use the given values to calculate the smallest and largest wavelengths of the light :
For the smallest wavelength, we need to find the maximum order of the interference minimum or maximum, which occurs when n = 0.
The maximum angle of the screen is 90°. Therefore, we can use the formula to calculate the wavelength :
λ = dsinθ/n
⇒λ = (0.002 m)sin(90°)/0
⇒λ = 0 m
This result means that there is no wavelength of light that will produce interference minima at an angle of 90° and order of zero. Therefore, there is no smallest wavelength of light that will produce interference minima at this angle.
For the largest wavelength, we need to find the minimum order of the interference minimum or maximum, which occurs when n = 1.
The minimum angle of the screen is given by sinθ = λ/d, which is equivalent to θ = sin⁻¹(λ/d).
Therefore, we can use the formula to calculate the wavelength for θ = sin⁻¹(400 × 10⁻⁹ m/0.002 m) :
λ = dsinθ/n
⇒λ = (0.002 m)sin(sin⁻¹(400 × 10⁻⁹ m/0.002 m))/1
⇒λ = 400 × 10⁻⁹ m
For θ = sin⁻¹(700 × 10⁻⁹ m/0.002 m) :
λ = dsinθ/n
⇒λ = (0.002 m)sin(sin⁻¹(700 × 10⁻⁹ m/0.002 m))/1
⇒λ = 700 × 10⁻⁹ m
Therefore, the smallest wavelength of light that will produce interference minima at visible light spectrum ranges from 400 nm to 700 nm is 400 nm, and the largest wavelength is 700 nm.
Thus, (a) the spacing between the slits is 570 nm or 0.57 microns ; (b) the smallest wavelength of light that will produce interference minima at visible light spectrum ranges from 400 nm to 700 nm is 400 nm, and the largest wavelength is 700 nm.
To learn more about wavelength :
https://brainly.com/question/16051869
#SPJ11
When one person shouts at a football game, the sound intensity level at the center of the field is 60.8 dB. When all the people shout together, the intensity level increases to 88.1 dB. Assuming that each person generates the same sound intensity at the center of the field, how many people are at the game?
Answers
Assuming that each person generates the same sound intensity at the center of the field, there are 1000 people at the football game.
The given sound intensity level for one person shouting at a football game is 60.8 dB and for all the people shouting together, the intensity level is 88.1 dB.
Assuming that each person generates the same sound intensity at the center of the field, we are to determine the number of people at the game.
I = P/A, where I is sound intensity, P is power and A is area of sound waves.
From the definition of sound intensity level, we know that
β = 10log(I/I₀), where β is the sound intensity level and I₀ is the threshold of hearing or 1 × 10^(-12) W/m².
Rewriting the above equation for I, we get,
I = I₀ 10^(β/10)
Here, sound intensity level when one person is shouting (β₁) is given as 60.8 dB.
Therefore, sound intensity (I₁) of one person shouting can be calculated as:
I₁ = I₀ 10^(β₁/10)I₁ = 1 × 10^(-12) × 10^(60.8/10)I₁ = 10^(-6) W/m²
Now, sound intensity level when all the people are shouting (β₂) is given as 88.1 dB.
Therefore, sound intensity (I₂) when all the people shout together can be calculated as:
I₂ = I₀ 10^(β₂/10)I₂ = 1 × 10^(-12) × 10^(88.1/10)I₂ = 10^(-3) W/m²
Let's assume that there are 'n' number of people at the game.
Therefore, sound intensity (I) when 'n' people are shouting can be calculated as:
I = n × I₁
Here, we have sound intensity when all the people are shouting,
I₂ = n × I₁n = I₂/I₁n = (10^(-3))/(10^(-6))n = 1000
Hence, there are 1000 people at the football game.
Learn more about sound intensity https://brainly.com/question/14349601
#SPJ11
A 1500-kg car moving east at 11 m/s collides with a 1780-kg car moving south at 15 m/s and the two cars stick together. (a) What is the velocity of the cars right after the collision? magnitude m/s direction -Select--- (b) How much kinetic energy was converted to another form during the collision? k]
Answers
By combining their momenta, we can determine the magnitude and direction of the velocity of the combined cars. The initial kinetic energy before the collision with the final kinetic energy are also compared.
After the collision, the two cars stick together and move as a single unit. To find their velocity right after the collision, we can apply the principles of conservation of momentum. The 1500-kg car is moving east at 11 m/s, while the 1780-kg car is moving south at 15 m/s.
Using the principle of conservation of momentum, we can determine the total momentum before the collision and set it equal to the total momentum after the collision. The momentum is given by the product of mass and velocity. We have:
(1500 kg × 11 m/s) + (1780 kg × 15 m/s) = (1500 kg + 1780 kg) × final velocity
By solving this equation, we can determine the magnitude and direction of the final velocity of the combined cars.
The kinetic energy converted to another form during the collision can be calculated by comparing the initial kinetic energy with the final kinetic energy. The initial kinetic energy is given by (1/2) × mass1 × velocity1² + (1/2) × mass2 × velocity2², and the final kinetic energy is given by (1/2) × (mass1 + mass2) × final velocity². The kinetic energy converted to another form is the difference between these two values.
By plugging in the given masses and velocities into the appropriate formulas, we can calculate the amount of kinetic energy converted during the collision.
Learn more about velocity here:
https://brainly.com/question/24135686
#SPJ11
"Calculate the electric field at a distance z=4.00 m above one
end of a straight line segment charge of length L=10.2 m and
uniform line charge density λ=1.14 Cm −1
Answers
The electric field at a distance z = 4.00 m above one end of a straight line segment charge of length L = 10.2 m and uniform line charge density λ = 1.14 Cm −1 is 4.31 × 10⁻⁶ N/C.
Given information :
Length of the line charge, L = 10.2 m
Line charge density, λ = 1.14 C/m
Electric field, E = ?
Distance from one end of the line, z = 4 m
The electric field at a distance z from the end of the line is given as :
E = λ/2πε₀z (1 - x/√(L² + z²)) where,
x is the distance from the end of the line to the point where electric field E is to be determined.
In this case, x = 0 since we are calculating the electric field at a distance z from one end of the line.
Thus, E = λ/2πε₀z (1 - 0/√(L² + z²))
Substituting the given values, we get :
E = (1.14 × 10⁻⁶)/(2 × π × 8.85 × 10⁻¹² × 4) (1 - 0/√(10.2² + 4²)) = 4.31 × 10⁻⁶ N/C
Therefore, the electric field at a distance z = 4.00 m above one end of a straight line segment charge of length L = 10.2 m and uniform line charge density λ = 1.14 Cm −1 is 4.31 × 10⁻⁶ N/C.
To learn more about electric field :
https://brainly.com/question/19878202
#SPJ11
A material has an index of refraction n = 1.78, the speed of the light in vacuum is c = 3 × 10^8 [m/s]. a. Which formula can be used to calculate the speed of the light in this material? b. The speed of the light in this material is given by: 01.78 x 3 x 10^8 3x10^8/1.78 1.78 /3x10^8 c. What is the speed of light in this material?
Answers
The formula that can be used to calculate the speed of light in a material is v = c / n. The speed of light in this material is approximately 1.69 × 10^8 meters per second.
a. The formula that can be used to calculate the speed of light in a material is:
v = c / n
where:
v is the speed of light in the material,
c is the speed of light in a vacuum,
n is the refractive index of the material.
b. The correct expression for the speed of light in this material is:
v = c / n
c. To calculate the speed of light in this material, we substitute the given values:
v = (3 × 10^8 [m/s]) / 1.78
v ≈ 1.69 × 10^8 [m/s]
Therefore, the speed of light in this material is approximately 1.69 × 10^8 meters per second.
To learn more about speed of light click here
https://brainly.com/question/1555553
#SPJ11
A solid 5.0 kg ball MR) with a radius of 2 m is released from rest on an incline. After t*3.9 seconds, the holl hos rolled 9.2 m down the incline. The minimum possible coefficient of static friction exists between the hill and all to keep the ball from slipping. What is the angle of the incline? Round to 2 decimal places 100 not include units in the final answer
Answers
The angle of the incline can be determined by calculating the coefficient of static friction required to prevent the ball from slipping. The angle of the incline is 25.3 degrees.
The first step is to calculate the linear acceleration of the ball. This can be done using the following equation:
a = g sin(theta)where:
* `a` is the linear acceleration of the ball
* `g` is the acceleration due to gravity (9.8 m/s^2)
* `theta` is the angle of the incline
Plugging in the known values, we get the following:
[tex]a = 9.8 m/s^2 sin(\theta)[/tex]
The next step is to use the linear acceleration to calculate the force of friction. This can be done using the following equation:
F = ma
where:
* `F` is the force of friction
* `m` is the mass of the ball (5.0 kg)
* `a` is the linear acceleration of the ball (calculated above)
Plugging in the known values, we get the following:
[tex]F = 5.0 kg \times 9.8 m/s^2 sin(\theta)[/tex]
The final step is to use the force of friction and the coefficient of static friction to calculate the angle of the incline. This can be done using the following equation:
F = μs N
where:
μs is the coefficient of static friction
N is the normal force
The normal force is equal to the weight of the ball, so we can substitute mg for N. This gives us the following equation:
[tex]\mu_ s mg = 5.0 kg \times 9.8 m/s^2 sin(\theta)[/tex]
Solving for `theta` gives us the following:
[tex]\theta = sin^{-1} (\mu_s \times g / 5.0)[/tex]
Plugging in the known value of `μs`, we get the following:
[tex]\theta = sin^{-1} (0.5 \times 9.8 m/s^2 / 5.0)[/tex]
[tex]\theta = 25.3 degrees[/tex]
Therefore, the angle of the incline is 25.3 degrees.
To learn more about angle of incline here brainly.com/question/16883538
#SPJ11
5. Two long straight wires are separated by distance d = 16.0 cm and carry currents I₁ = 3.0 A and I₂ = 12.0 A out of the page as shown in the figure. On the x axis, find the location of the point (relative to wirel) where the net magnetic field of the two wires is zero. Note that there are three regions to consider on the x axis: to the left of wire 1, between wirel and wire2, and to the right of wire2. Sketch the direction of magnetic fields to support your answer. (12pts) O X
Answers
The location where the net magnetic field of the two wires is zero is at x = +3.2 cm relative to wire 1.
To find the location where the net magnetic field of the two wires is zero, we can use the principle of superposition and consider the magnetic fields produced by each wire separately.
Let's first analyze the magnetic field produced by wire 1 and determine its direction. According to the right-hand rule for the magnetic field around a current-carrying wire, the magnetic field lines produced by wire 1 form concentric circles around the wire.
Using the right-hand rule, we can determine that the magnetic field produced by wire 1 points in the counterclockwise direction when viewed from above the wire.
Next, let's analyze the magnetic field produced by wire 2. Similarly, the magnetic field lines produced by wire 2 form concentric circles around the wire, but in the opposite direction compared to wire 1.
Using the right-hand rule, we can determine that the magnetic field produced by wire 2 points in the clockwise direction when viewed from above the wire.
To find the location where the net magnetic field is zero, we need to determine the point on the x-axis where the magnetic fields produced by wire 1 and wire 2 cancel each other out.
This occurs when the magnetic fields have equal magnitudes but opposite directions.
Let's consider the three regions on the x-axis:
1. To the left of wire 1: In this region, the magnetic field produced by wire 1 is the dominant one, and there is no magnetic field from wire 2. Therefore, the net magnetic field is not zero in this region.
2. Between wire 1 and wire 2: In this region, the magnetic fields from both wires contribute to the net magnetic field. The distance between the wires is given as d = 16.0 cm.
To find the location where the net magnetic field is zero, we can apply the principle that the magnetic field produced by wire 1 at that point is equal in magnitude but opposite in direction to the magnetic field produced by wire 2.
Using the formula for the magnetic field produced by a long straight wire:
[tex]\[B = \frac{{\mu_0 \cdot I}}{{2 \pi \cdot r}}\][/tex]
where B is the magnetic field, μ₀ is the permeability of free space, I is the current, and r is the distance from the wire, we can equate the magnitudes of the magnetic fields:
[tex]\[\frac{{\mu_0 \cdot I₁}}{{2 \pi \cdot r}} = \frac{{\mu_0 \cdot I₂}}{{2 \pi \cdot (d - r)}}\][/tex]
Simplifying the equation, we have:
[tex]\rm I_1 \cdot (d - r) = I_2 \cdot r\][/tex]
Substituting the given values, I₁ = 3.0 A, I₂ = 12.0 A, and d = 16.0 cm = 0.16 m, we can solve for r:
[tex]\[3.0 \cdot (0.16 - r) = 12.0 \cdot r\]\\\\0.48 - 3.0r = 12.0r\]\15.0r = 0.48\]\r = \frac{{0.48}}{{15.0}}\]\\\\r = 0.032 \, \\\\\text{m} = 3.2 \, \text{cm}\][/tex]
Therefore, the location where the net magnetic field of the two wires is zero is at x = +3.2 cm relative to wire 1.
3. To the right of wire 2: In this region, the magnetic field produced by wire 2 is the dominant one, and there is no magnetic field from wire 1. Therefore, the net magnetic field is not zero in this region.
Know more about the magnetic field:
https://brainly.com/question/19542022
#SPJ4
QUESTION 1 A student measures the diameter (D) of a cylindrical wire using micrometer of accuracy (0.01mm) as shown in the figure. What is the reading of the measured diameter? 0 5 10 10 5
Answers
The reading of the measured diameter is 10.05 mm. The micrometer has an accuracy of 0.01 mm, which means it can measure values with two decimal places.
The reading on the micrometer scale consists of the whole number part and the fractional part.
In this case, the whole number part is 10 mm, and the fractional part is 0.05 mm. The fractional part is read from the circular scale on the micrometer, which is divided into smaller increments.
Therefore, when the cylindrical wire is measured using the micrometer, the reading for the diameter is 10.05 mm, indicating a whole number part of 10 mm and a fractional part of 0.05 mm.
Learn more about diameter here: brainly.com/question/5501950
#SPJ11